Ficha

   TECHNICAL DATA SHEET – LINE-X® XS-100

PRODUCT MANUFACTURER:

LINE-X® Franchise Development Company 6 Hutton Centre Drive, Suite 500 Santa Ana, CA 92707

Resin “B” Block Heater: Hoses (Iso and Polyol): Hydraulic Pressure Setting Equipment Hydraulic Pressure:

140-160°F 130-150°F 2,0002,500 PSI

GENERAL PRODUCT DESCRIPTION:

LINE-X XS-100 is a two-component, high performancearomatic polyurea/polyurethane hybrid spray elastomer system zero VOC (Volatile Organic Compounds), 100% solid. LINE-X XS-100 offers outstanding performance and superior elastomeric protective coatings for various substrates. LINE-X XS-100 is designed as a user-friendly product with a built-in activator for quick cure times, and offers exceptional adhesion properties on properly prepared substrates. Thehigh performance formulation of LINE-X XS-100 produces an excellent skin formation for chemical resistance and moisture protection.

EQUIPMENT CLEAN-UP:

Spray equipment should be cleaned immediately after use following equipment manufacturer’s recommended procedures. Please refer to spray equipment operating and maintenance procedures for further details. LINE-X XS-100 should be cleaned withenvironmentally safe urethane-grade cleaners. Cleaning materials must be free of reactive contaminants such as water and alcohol. All gun cleaners and spray equipment cleaning materials must be used and disposed of as permitted under local rules and regulations.

APPLICATION GUIDELINES:

MATERIAL STORAGE:

Both the Iso “A” Side and Resin “B” Side should be preconditioned between 70-90°Fbefore application. LINE-X XS-100 must be applied using high-pressure, plural component, heated, 1:1 by volume, spray equipment with 2000 PSI fluid pressure capability. LINE-X XS-100 material (both Iso “A” Side and Resin “B” Side) should be heated between 120-150°F. Spray equipment must generate adequate fluid pressure for proper mixing and best polymerization results.

LINE-X XS-100 has a shelflife of twelve (12) months from manufacture date in factory sealed containers. LINE-X XS-100 should be stored between 65-80°F. Do not expose unused materials to high humidity conditions. Always provide airtight reseal conditions to unused materials. For materials that are currently connecting to the pumps, always provide as much airtight and moisture-free conditions to unused materials as possible toensure proper chemical performance. Drums should be stored on pallets to avoid direct contact with the warehouse floor/ground.

APPLICATION EQUIPMENT:

LINE-X XS-100 is designed to be sprayed through high pressure impingement mixing equipment. Plural component spray equipment must have material heat-control capability, 1:1 by volume, and sprayable with round or flat tip. Refer to equipmentmanufacturer for equipment specifics and accessories.

SAFETY AND HANDLING:

Please refer to MSDS for safety and handling of this material. All personnel working with this material are expected to read and understand all safety recommendations per MSDS. All Personal Protection Equipment must be properly worn to comply with worker health and safety requirements.

EQUIPMENT SETTING PARAMETERS:CHEMICAL TECHNICAL DATA:

Iso “A” and Polyol “B” components must be pumped by low-pressure transfer pumps to a suitable high-pressure proportional pumping system. Temperature Settings Iso “A” Block Heater: 140-160°F

Mix Ratio by Volume: Gel Time: Tack Free Time: Viscosity (cPs) @ 77°F. “A” Iso Side: “B” Resin Side: Material Density (lbs/gal) @ 77°F.

1A:1B 3-6 Sec 6-9 Sec 550±100 1100±100Rev. 05.09

   TECHNICAL DATA SHEET – LINE-X® XS-100
“A” Iso Side: “B” Resin Side: 9.6 lbs/gal 9.0 lbs/gal

BASIC PHYSICAL PROPERTIES:

All tests are performed by OCM Test Laboratories. • ISO 17025 Certified • American Association for Laboratory Accreditation (A2LA) Test Name
Hardness Shore D Coefficient of Friction Static Kinetic Dielectric Const. Dissipation Factor Volume...