Fdfsdf

Designation: B 150/B 150M – 03

Standard Specification for

Aluminum Bronze Rod, Bar, and Shapes1
This standard is issued under the fixed designation B 150/B 150M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon(e) indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.

1. Scope * 1.1 This specification establishes the requirements for aluminum bronze rod, bar, and shapes for Copper Alloys UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210.
NOTE 1—Product intended forhot forging is described in Specification B 124/B 124M. NOTE 2—Warning—Mercury is a definite health hazard in use and in disposal.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systemsmay result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. 2. Referenced Documents 2.1 ASTM Standards: B 124/B 124MSpecification for Copper and Copper Alloy Forging Rod, Bar and Shapes2 B 154 Test Method for Mercurous Nitrate Test for Copper and Copper Alloys2 B 249/B 249M Specification for General Requirements for Wrought Copper and Copper Alloy Rod, Bar and Forgings2 B 601 Practice for Temper Designations for Copper and Copper Alloys—Wrought and Cast2 B 858 Test Method for Ammonia Vapor Test for DeterminingSusceptibility to Stress Corrosion Cracking in Copper Alloys2
1 This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod, Bars, Wire, Shapes and Forgings. Current edition approved May 10, 2003. Published June 2003. Originally approved in 1941. Last previous edition approved in 2002 as B 150/B 150M – 02. 2Annual Book of ASTM Standards, Vol 02.01.

E 8 Test Methods for Tension Testing of Metallic Materials3 E 8M Test Methods for Tension Testing of Metallic Materials [Metric]3 E 18 Test Methods for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials3 E 53 Test Methods for Chemical Analysis of Copper4 E 62 Test Methods for Chemical Analysis of Copper and Copper Alloys (PhotometricMethods)4 E 118 Test Methods for Chemical Analysis of Copper— Chromium Alloys4 E 478 Test Methods for Chemical Analysis of Copper Alloys4 3. General Requirements 3.1 The following sections of Specifications B 249/B 249M constitute a part of this specification: 3.1.1 Terminology, 3.1.2 Materials and Manufacture, 3.1.3 Workmanship, Finish, and Appearance, 3.1.4 Sampling, 3.1.5 Number of Tests andRetests, 3.1.6 Specimen Preparation, 3.1.7 Test Methods, 3.1.8 Significance of Numerical Limits, 3.1.9 Inspection, 3.1.10 Rejection and Rehearing, 3.1.11 Certification, 3.1.12 Mill Test Report, 3.1.13 Packaging and Package Marking, Preservation and Delivery, and 3.1.14 Supplementary Requirements. 3.2 In addition, when a section with a title identical to those referenced in 3.1, appears in thisspecification, it contains additional requirements that supplement those appearing in Specification B 249/B 249M. 4. Ordering Information 4.1 Include the following information when placing orders for product under this specification:
3 4

Annual Book of ASTM Standards, Vol 03.01. Annual Book of ASTM Standards, Vol 03.05.

*A Summary of Changes section appears at the end of this standard.
Copyright...